Automotive

Category: Product News

Efficient Fault Simulation – Automated, documented short-circuit and open load tests of ECU on-board diagnostics

Efficient Fault Simulation by Softing

In daily operation, ECUs in the vehicle are exposed to a wide range of environmental influences, such as vibrations, strongly fluctuating ambient temperatures and high humidity. The components must therefore be able to handle all conceivable faults. For the test, these faults are simulated on the ECU pin and the respective behavior and diagnostic entry documented. Typically, such fault simulations are used for function tests during development, for testing, release and validation of ECUs and components, as well as for integration validation during HiL testing or at the Functional Mock-Up (FMU).

Pole-Position with the Telematics Gateway xTCU

Pole-Position with the Telematic Gateway xTCU

With the xTCU telematics gateway from Globalmatix in combination with Memotec measurement technology – comprehensive information everywhere in real time. In racing, it is often just tiny details that make the difference between victory and defeat. In addition to the driver’s skill, it also depends on the racing team having the appropriate expertise. Among other things, data acquisition and measurement technology is installed in the vehicle in order to constantly monitor and ultimately optimize it.

SOVD – The Diagnostic Standard of Tomorrow

SOVD - Service Oriented Vehicle Diagnostics

Due to current megatrends such as autonomous driving, significantly higher computing power is required in the vehicle than can be provided by today's ECUs. Consequently high-performance computers (HPCs) are being installed in the vehicle to implement both centralized control and diagnostic functions. Standardization of the interface is therefore an obvious step, and is currently being carried out in ASAM e.V. under the name SOVD (Service Oriented Vehicle Diagnostics).

Individual test equipment for maximum reliability in engineering and tests

Test Equipment by Softing

A large number of different cables, adapters and peripheral simulations are used in the engineering of vehicle electronics, the testing of electronic and electrical components and in component integration into the complete vehicle. The use of standard products is rarely possible here. Test equipment specially adapted to the control unit, vehicle series or test environment is nearly always required.

Success Story Bosch Rexroth: Intelligent Diagnostics for Mobile Electronics and Machines of the Future

Success Story Bosch Rexroth: Intelligent Diagnostics for Mobile Electronics and Machines of the Future

BODAS-service 4.x – More than Maintenance and Repair | powered by Softing TDX: Mobile working machinery is an important segment of the entire vehicle market. Typically the machinery requires hydraulic drive technology, especially axial piston units, which make displacement with high pressure possible. The operating and environmental conditions in this segment are much tougher than for standard motor vehicles.

Test Boards by Softing: Working as if you were working on a verhicle – but with full comfort!

Test Boards by Softing

A range of original components can be conveniently attached and connected to each other on test boards according to their target arrangement in the vehicle. This is the perfect way to subject, in particular, the cable harness and ECUs to complex networking and function tests in conjunction with real sensors, actuators and other subsystems. Test boards thus enable flexible tests for series validation – long before tests are possible on real vehicles.

Softing DTS 9: New Generation of the All-in-One Engineering Tester Now Available!

Softing DTS 9 - the new generation

Following the successful launch at pilot customers, the new generation of the high-performance and use-case-optimized Diagnostic Tool Set (Softing DTS 9) is now available. New functionalities enable even faster and more cost-efficient diagnostic development – exactly what is needed for the growing complexity of E/E architectures and shorter product development cycles Softing DTS.monaco makes it possible for developers, engineers and technicians to create consistent diagnostic functions and sequences on the basis of international standards and to ensure that diagnostic communication works reliably over the entire value chain.

Configuration Tool for Central Role and User Management from the Softing TDX Toolkit

Softing TDX.admin – Configuration Tool for Central Role and User Management

The large number of diagnostic tester installations (Softing TDX.workshop) all over the world makes the efficient management of role and user authorizations particularly important. In addition, ensuring consistent, automated and centrally controlled updates of software and its diagnostic content, such as repair instructions and diagnostic trees, is of particular importance for the use of the diagnostic tester in the repair shop area. We meet these challenges with Softing TDX.admin, a backend administrator tool from the Softing TDX toolkit.

Design Options in Softing DTS.monaco – Interactively and Individually Designable User Interfaces

Design options in Softing DTS.monaco

With the new generation of the Diagnostic Tool Set – Softing DTS 9 – the integration of OTX sequences in the Monaco workspaces now makes it possible for entire release sequences, continuous operation controls as well as certifications to be safely integrated into the working environment to prevent operating errors. OTX allows you to freely define both the user interfaces and the stored diagnostic sequence.

«